Custom Truck Parts & Fabrication by Eastside Custom Truck, ECT » ECT Rocker Parts
ECT Rocker Parts were designed to compliment any custom built chassis or Jeep. Rocker Parts are precision machined for accuracy and the perfect fit. Rocker Parts are anodized for good looks.
ECTs new line of Rocker Parts, will help putthe finishing touches on your your project. Rocker Parts are CNC machine to exact spec for a perfect fit, and easy installation.
Tired of breaking that stock Dana 30? Have you gone to larger tires? Looking to find a Dana 44 Axle to bolt on right under your Jeep Wrangler TJ, Jeep Cherokee XJ, 93-98 Jeep Grand Cherokee ZJ, &...More Details »
Slip Yoke Eliminator Kits are used for converting to a drive shaft with a slip shaft. Slip Yoke Eliminator Kits also allow for the use of a CV Style Drive Shaft. These kits are a must for Jeep Vehicles with 3.5 inches of lift or more.
Jam nuts counter tighten against componenets to keep them tightly in place. Jam Nuts also keep the elements out of the threads by creating binding pressure against components which creates a seal against the threads.
Upgrade your existing suspension with hydraulic bump stops or "air bumps" to smooth harsh, or rough riding suspension. Protect the rest of your suspension and vehicle from impacts and prevent...More Details »
Description: 1280 Series 10 Spline U-Joint Yoke
10 Spline Transfer Case Yoke
**Includes new shaft nut**
Fits Jeep CJ V6 Transfer case, where clearance is limited between drive shaft and transmission.
Description: 1350 Series U-Joint Flange Yoke
May be used with CV style shaft or Non CV style shaft
Includes Studs
May be used on Front or Rear Output of transfer case.
**Seal with 2.125" ID Required**...More Details »
Description: 1310 Series U-Joint Yoke
29 Spline Transfer Case Yoke
**Eliminates interference between pinion nut and U-joint at severe angle eliminating vibration problems**
U-Bolt Style Hardware
Description: 1350 Series U-Joint Flange
May be used with CV style shaft or Non CV style shaft
Includes Studs
May be used on Front or Rear Output of transfer case.
**Seal with 2.125" ID Required**
Flange...More Details »
Description: Lever operated - 6-36 volt, 180 amps.
Continuous capacity 1,000 amps in rush S.P.S.T. (On-Off), two stud terminals.
For battery circuit only.
Does not disconnect alternator or...More Details »
Description: 1984-2001 Jeep Cherokee XJ Dana 44 Front Assembly
-We use only quality new components in building your Dana 44, from the top manufactures such as; Dana Spicer, Timken, Alloy USA, and more....More Details »
Item #: ECT1101848
Condition: New
All axle assemblies
are built to your
specs. Axles are
built in the order
they are received
and maybe subject to
component
Please call us for a freight quote to your location. Remember a commercial address is most cost effective. Axles are shipped on a pallet and can be "will call" at a local depot.
Description: 1986-1988 Jeep Comanche MJ Dana 44 Front Assembly
-We use only quality new components in building your Dana 44, from the top manufactures such as; Dana Spicer, Timken, Alloy USA, and more....More Details »
Item #: ECT1094204
Condition: New
All axle assemblies
are built to your
specs. Axles are
built in the order
they are received
and maybe subject to
component
Please call us for a freight quote to your location. Remember a commercial address is most cost effective. Axles are shipped on a pallet and can be "will call" at a local depot.
Description: 1993-1998 Jeep Grand Cherokee ZJ Dana 44 Front Assembly
-We use only quality new components in building your Dana 44, from the top manufactures such as; Dana Spicer, Timken, Alloy USA, and...More Details »
Item #: ECT1349905
Condition: New
All axle assemblies
are built to your
specs. Axles are
built in the order
they are received
and maybe subject to
component
Please call us for a freight quote to your location. Remember a commercial address is most cost effective. Axles are shipped on a pallet and can be "will call" at a local depot.
See All »
